Why Is My Check Engine Light On In My Jeep Grand Cherokee?

Why is my check engine light on in my Jeep Grand Cherokee? 2020 Jeep Grand Cherokee Check Engine Light Flashing

Other common reasons for a Check Engine Light are dirty mass airflow sensor, a malfunction with the fuel injection system, damaged oxygen sensor, faulty emissions control part, faulty head gasket, or defective spark plugs to name a few.

How do you reset the check engine light on a 2006 Jeep Grand Cherokee?

To turn off the Jeep Grand Cherokee check engine light, turn the ignition switch to ON but don't start the vehicle. Press the gas pedal 3 times within 10 seconds and turn the ignition off. Wait 10 seconds and start the engine.

Why is my Jeep check engine light on?

Jeep Wrangler Check Engine Light Flashing

Other common reasons for a Check Engine Light are faulty head gasket, a malfunction with the fuel injection system, dirty mass airflow sensor, faulty emissions control part, damaged oxygen sensor, or defective spark plugs to name a few.

How do you reset the check engine light on a Jeep?

  • Make sure the engine is not running and key is out of the ignition.
  • Disconnect the battery terminals.
  • Wait 5 minutes.
  • Reconnect battery terminals.
  • Insert and turn the ignition key to the run position without starting.
  • All error codes are cleared and CHECK ENGINE icon disappeared.
  • How do you reset the codes on a Jeep Grand Cherokee?

  • Pull the release lever to open the hood from inside the vehicle.
  • Open the hood and place the support rod into position to prop up the hood.
  • Remove the nut connecting the negative battery terminal to the battery, using an open end wrench.
  • Allow the computer to reset.

  • Related advices for Why Is My Check Engine Light On In My Jeep Grand Cherokee?


    What could be wrong when check engine light is on?

    The light could be a minor issue, such as a faulty gas cap, or it could mean something more serious, such as a misfiring engine. If the light begins flashing, however, it indicates a more serious problem, such as a misfire that can quickly overheat the catalytic converter.


    What does a check engine light look like on a Jeep Cherokee?

    If the check engine light in your Jeep Cherokee starts flashing, that means that the problem needs sudden attention and your Jeep should be brought in today. This blinking light mostly indicates a scrupulous engine misfire allowing unused fuel to be deposited into the exhaust system.


    How do you check a check engine light on a Jeep?

    Insert your key and turn the ignition to the On position without starting the vehicle. Then, push the key into the ignition cylinder and (while holding it in) turn it to Off then On three times - making sure to end in the ON position.


    How much does it cost to get your check engine light checked?

    There's a lot that goes on inside your engine, and rooting out the problem and fixing it can be a costly proposition. How costly? On average, the fee to have an auto mechanic diagnose a check engine light is $100.


    What does an orange engine light mean?

    The orange, engine-shaped icon on your car dashboard's instrument cluster is programmed to turn on when the vehicle's electronic brain detects something is wrong. Don't panic if you see it — it doesn't necessarily mean you'll need to give your next paycheck to the nearest mechanic.


    Can check engine light turn itself off?

    A check engine light will shut itself off if the condition that caused it is remedied. If you then did a bunch of highway driving before changing the oil, the specs may have dropped back into the normal range, causing the light to go off.


    Does disconnecting battery reset check engine light?

    Leaving the battery disconnected for about 15 minutes will ensure the vehicle systems will completely reset when you reconnect the battery. Disconnecting the battery will clear the error codes and reset the check engine light.


    How do you reset the check engine light with a gas pedal?

    Press the gas pedal completely down with your foot and hold it there for 10 seconds, or until the SES light blinks on and off.


    How do you clear a gas cap code?

  • Turn off your vehicle's engine.
  • Step to the gas cap door.
  • Replace the gas cap.
  • Close the gas cap door.
  • Use an OBD-II code scanner if the warning light does not disappear.
  • Continue driving the vehicle.

  • What does error code P0128 mean?

    The P0128 code means that the engine coolant is not getting warm enough, fast enough. In other words, there is a problem with the engine operating temperature not being reached within a certain amount of time. The Engine Control Module (ECM) determines this length of time based on ambient temperature.


    How do you reset the check engine light on a 2004 Jeep Grand Cherokee?

  • Disconnect the positive (red) battery cable.
  • Ground the positive battery cable to negative (black) battery cable for around 30 seconds.
  • Reconnect the positive battery cable.
  • Turn your key into the "ON" position, but do not turn on the engine.

  • How do I find my Jeep Grand Cherokee engine code?

  • Get behind the Grand Cherokee's wheel and slide your key into the ignition. Turn the key in the following pattern: On-Off-On-Off-On.
  • Grab a pen and paper and count the number times the check engine light flashes at you. It will be a code.

  • Can a blown fuse cause check engine light to come on?

    A check engine light can be caused by a fuse. Multiple codes can be set at one time.


    What would cause a Jeep Cherokee to not start?

    While there are a variety of reasons your Jeep Cherokee won't start, the most common 3 are a dead battery, an alternator problem, or failed starter.


    Was this post helpful?

    Leave a Reply

    Your email address will not be published.